HyPhy message board | |
http://www.hyphy.org/cgi-bin/hyphy_forums/YaBB.pl
HYPHY Package >> HyPhy bugs >> ModelSelectorCodon.bf bug? http://www.hyphy.org/cgi-bin/hyphy_forums/YaBB.pl?num=1281401004 Message started by Matt on Aug 9th, 2010 at 5:43pm |
Title: ModelSelectorCodon.bf bug? Post by Matt on Aug 9th, 2010 at 5:43pm
Using either HYPHYMPI or HYPHYMP....
my bf: Code (]inputOptions = {}; inputOptions ["00"):
I always get this error: Code (]Log Likelihood = -2999.54815749801; Shared Parameters: NSR0=1.05924 G3=0.549061 G2=0.313017 G1=0.446134 C3=0.317419 C2=0.266713 C1=0.22303 A3=0.229822 A2=0.391362 A1=0.273183 AC=0.295982 Tree codon_tree_1=[deleted for the purposes of this post..):
|
Title: Re: ModelSelectorCodon.bf bug? Post by Sergei on Aug 10th, 2010 at 12:05pm
Hi Matt,
This analysis must be run in an MPI environment; sorry for the lack of meaningful error messages. Sergei |
Title: Re: ModelSelectorCodon.bf bug? Post by Matt on Aug 10th, 2010 at 1:21pm
Hi Sergei,
The thing is, with the HYPHYMPI, the program appears to be non-responsive for hours, at which time I grow impatient and kill it. This is using the .bf that I included in the original post. I'm running GARD and GABranch and a few other things using MPI, so I'm 100% sure that the MPI environment is OK. The same .bf, using HYPHYMP, proceeds through several steps (again, copied in original post) within minutes, before it dies. So, is this a case where the screen output is different between the MPI and MP versions, or is there something else going on? If the former, you might consider, for future HYPHY release, adding a status indicator or some sort of output that would allow the used to have confidence that the program is working as intended.. Most of the algorithms already have such an output. Thanks! |
Title: Re: ModelSelectorCodon.bf bug? Post by Sergei on Aug 10th, 2010 at 1:25pm
Hi Matt,
You should get some feedback on the progress pretty quickly (almost immediately for the first few steps), but this IS a slow analysis (a few hours at least). How big is your alignment? I'll also check the settings in your run to confirm that the code isn't simply hanging and waiting for input. Thanks for your feedback! Sergei |
Title: Re: ModelSelectorCodon.bf bug? Post by Matt on Aug 10th, 2010 at 1:33pm
85 sequences of length 300bp.
I get no screen output from this analysis, simply a blinking cursor.. In other analyses, when I screw up the batchfile by forgetting to add something or misspelling an input option, HYPHYMPI usually just seg faults.. |
Title: Re: ModelSelectorCodon.bf bug? Post by Sergei on Aug 10th, 2010 at 1:41pm
Hi Matt,
Thanks; this behavior is not normal. I will check if I can reproduce the issue on my installation with the settings that you selected. Sergei |
Title: Re: ModelSelectorCodon.bf bug? Post by Matt on Aug 29th, 2010 at 5:10am
Hi Sergei,
Any update on this issue? Thanks, Matt |
Title: Re: ModelSelectorCodon.bf bug? Post by Sergei on Aug 29th, 2010 at 3:33pm
Hi Matt,
Sorry about the delay -- your question slipped through the cracks. I will take a look tomorrow and see what I can find. Sergei |
Title: Re: ModelSelectorCodon.bf bug? Post by Sergei on Aug 31st, 2010 at 12:37pm
Hi Matt,
Try adding 'inputOptions' as the second argument to ExecuteAFile (as shown in the quoted code below) -- without this option the analysis will not use your presets as input, and running HYPHYMPI in an MPI will probably simply hang waiting for stdin. I tried running your input on a random codon file with ~50 sequences and all went well. Also, the recommended option for inputOptions ["08"] is "BIC" (as "c-AIC" leads to some overfitting). Sergei Matt wrote on Aug 9th, 2010 at 5:43pm:
|
HyPhy message board » Powered by YaBB 2.5.2! YaBB Forum Software © 2000-2024. All Rights Reserved. |